(1) Glue compounding on the composite board: check whether the panel and bottom plate of the composite board production line are dry, and pick out the board with moisture. (1) تركيب الغراء على اللوح المركب: تحقق مما إذا كانت اللوحة واللوحة السفلية لخط إنتاج اللوح المركب جافة ، واختر اللوح بالرطوبة. Adjust the glue, adjust the glue and calcium carbonate evenly, and adjust the toner to the same color as the panel. اضبط الغراء ، واضبط الغراء وكربونات الكالسيوم بالتساوي ، واضبط الحبر على نفس لون اللوحة. According to the climate and humidity at the time, add an appropriate amount of curing agent, the ratio of curing agent to glue is 1 ~ 3%. وفقًا للمناخ والرطوبة في ذلك الوقت ، أضف كمية مناسبة من عامل المعالجة ، فإن نسبة عامل المعالجة إلى الغراء هي 1 ~ 3 ٪.
(2) Pre-composite process of panel: if faced with a polished surface and a mesh panel, it must be carefully selected and sent to a hand-held grinder for de-glazing. (2) عملية ما قبل التركيب للوحة: إذا واجهت سطحًا مصقولًا ولوحة شبكية ، فيجب تحديدها بعناية وإرسالها إلى طاحونة يدوية لإزالة الزجاج. It is de-aired according to the flatness, dry-grinded and leveled, but not deep-grinded; يتم تفريغه وفقًا للتسطيح ، والطحن الجاف والتسوية ، ولكن ليس الطحن العميق ؛ then the net is broken off Cloth shovel flat surface glue. ثم يتم قطع الشبكة عن غراء مجرفة القماش المسطح. If the shovel cannot be removed, you should use a hand-held grinder to grind off the net surface glue. إذا لم يكن بالإمكان إزالة المجرفة ، فيجب عليك استخدام مطحنة يدوية لطحن الغراء على سطح الشبكة. Use double-sided smoothing to remove dust from the dry-milled panel. استخدم تجانس الوجهين لإزالة الغبار من لوحة الطحن الجاف.
(3) The pre-composite process of the bottom plate: the bottom plate with light should be de-glazed and then thickened, usually the thickness of 20mm bottom plate should be 17mm. (3) عملية ما قبل المركب للوحة السفلية: يجب إزالة الصفيحة السفلية مع الضوء ثم تزجيجها ، وعادة ما يكون سمك اللوحة السفلية 20 مم 17 مم. After the bottom plate is fixed, remove moisture. بعد تثبيت اللوحة السفلية ، قم بإزالة الرطوبة. Can be pulled outside to dry, dry or blow dry. يمكن سحبه للخارج ليجف ، يجف أو يجف. Note that if the board is not dry, it cannot be glued to avoid delamination or infirmity. لاحظ أنه إذا لم يكن اللوح جافًا ، فلا يمكن لصقه لتجنب التصفيح أو الضعف.
(4) Select panel: select the marble panel that meets the customer's requirements. (4) حدد اللوحة: حدد اللوحة الرخامية التي تلبي متطلبات العميل. Clarify the types of materials and the consistency of colors. وضح أنواع المواد واتساق الألوان. Note that when selecting the panel, it should be free of scars, warpage, trachoma, depressions, stains, etc. If the wool board does not show the effect, the panel can only be determined after spraying the board with a water gun. لاحظ أنه عند اختيار اللوحة ، يجب أن تكون خالية من الندوب ، والالتفاف ، والتراخوما ، والاكتئاب ، والبقع ، وما إلى ذلك. إذا لم يظهر لوح الصوف التأثير ، فلا يمكن تحديد اللوحة إلا بعد رش اللوحة بمسدس مياه.
اتصل شخص: Mr. Arno Hao
الهاتف :: +8618717894416