The main part of the cold bending forming equipment is the roller. الجزء الرئيسي من معدات تشكيل الانحناء البارد هو الأسطوانة. The design of the roll is very important, and its design features are as follows: إن تصميم اللفة مهم للغاية ، وميزات تصميمها هي كما يلي:
1. مبدأ متوسط القوة لكل ممر من معدات تشكيل الانحناء البارد ، متوسط قوة الأسطوانة ، التآكل متوازن ، وزيادة عمر خدمة الأسطوانة.
2. The material used for the roll is to use its wear resistance, but the specific strength and hardness are contradictory. 2. المواد المستخدمة للفة هي استخدام مقاومة التآكل ، ولكن القوة والصلابة المحددة متناقضة. The red hardness of C12MoV should be used during heat treatment. يجب استخدام الصلابة الحمراء لـ C12MoV أثناء المعالجة الحرارية. After quenching, the hardness can be achieved by two to three tempers. بعد التبريد ، يمكن تحقيق الصلابة من خلال اثنين إلى ثلاثة درجات حرارة.
3. The arc part of the track is the main part of the cold bending forming equipment. 3. الجزء القوسي من الجنزير هو الجزء الرئيسي من معدات تشكيل الانحناء البارد. The arc position after the first few press forming, when the vertical edge is rolled in the subsequent pass, the formed arc should be protected by the upper and lower rolls or the horizontal wheel. وضع القوس بعد تشكيل الضغط القليلة الأولى ، عندما يتم لف الحافة الرأسية في التمرير اللاحق ، يجب حماية القوس المتشكل بواسطة القوائم العلوية والسفلية أو العجلة الأفقية. Tube bundle. حزمة أنبوب. Otherwise, the arc position of the material will change during the stretching process, R becomes smaller and becomes triangle, and when the shape R becomes larger, the matching rail will sway, uneven stress, the rail will be deformed, and the service life will be reduced. خلاف ذلك ، سيتغير موضع القوس للمادة أثناء عملية التمدد ، ويصبح R أصغر ويصبح مثلثًا ، وعندما يصبح الشكل R أكبر ، سيتأرجح السكة المطابقة ، والضغط غير المستوي ، وسوف يتشوه السكة ، وسوف يتغير عمر الخدمة يتم تخفيض.
4. Rolling stability problem, the problem of deflection of the material in the raceway is often encountered during production. 4. مشكلة الاستقرار المتداول ، غالبا ما تصادف مشكلة انحراف المواد في القناة أثناء الإنتاج. In fact, a single set of rollers is asymmetric, the left side is stressed, and the material deflects to the right; في الواقع ، مجموعة واحدة من البكرات غير متناظرة ، والضغط على الجانب الأيسر ، وتنحرف المادة إلى اليمين ؛ the right side is stressed, the material Swing to the left يتم التأكيد على الجانب الأيمن ، تتأرجح المواد إلى اليسار
اتصل شخص: Mr. Arno Hao
الهاتف :: +8618717894416